Parts & Accessories
The Wahoo RPM cadence sensor is your sleek little solution for measuring cycling cadence data. It is wireless, magnet-less, lightweight, and easily mounts to your bike's crank arm or to your shoe. Bluetooth Smart and ANT+ dual band technology allows you to connect to and display data on both smartphones and GPS bike computers. Collecting cadence data has never been this easy. - Both ANT+ and Bluetooth Smart capabilities allow for a wireless connection to both smartphones and bike computers. - No tangled wires on your bike to connect the sensor to your device. - It only weighs 7 grams! - Provides accurate cadence data during your ride - (1) mount with double sided 3M tape, or (2) use the silicone sleeve and mount with zip ties. - The RPM can be worn on your shoe for spin classes or use with multiple bikes - Two LED lights show the sensor's device connection (blue) and cadence detection (red) - No charging required! Operates on a coin cell battery for up to 1 years. - RPM cadence sensor will fit with most bikes and frame sizes
The Wahoo RPM speed sensor is the sleek, magnet-less solution for capturing cycling speed data. It easily mounts to your bike's front wheel hub, and the Bluetooth Smart and ANT+ dual band technology allow you to connect to and display data on both smartphones and bike computers. Tracking speed data has never been this easy. - Both ANT+ and Bluetooth Smart capabilities allow for a wireless connection to both smartphones and bike computers. - No tangled wires on your bike to connect the sensor to your device. - The RPM speed installs easily with no magnets required - It only weighs 16.5 grams with the mount included - Provides accurate speed data during your ride - Mounts on most front wheel hub with a secure silicone casing - Two LED lights show the sensor's device connection (blue) and speed detection (red) - No charging required! Operates on a coin cell battery for up to 1 years. - RPM Speed will fit with most bikes and frame sizes
All you need for cycling data, all together at once! The Wahoo RPM Speed and Cadence sensors are both a sleek, wireless, and magnet-less solution. Each mounts easily to your bike and the Bluetooth Smart and ANT+ duel band technology allows you to connect and display data on both smartphone and bike computers. - Dimensions (LxWxH): 1.25" x.75" x 1" - Weight: 7 grams (without mount) - Battery: CR2032 - Battery Life: Up to 12 months - Water Rating: IPX7 (waterproof up to 5 ft) - Wireless Signal Strength: Up to 10 feet - Note: Speed Sensor is NOT compatible with spin bikes
Charge your Specialized Turbo battery with this high output, custom Li-ion charger. • Custom Specialized Li-ion battery charger • Output: 42V4A • Compact design while delivering huge power • With Rosenberger plug and light indication of the charging status
Shimano BT-R1A External Di2 Battery - All Di2 components on the bicycle require the same firmware version. Using Di2 components with different firmware versions may cause malfunctions - Use Di2 system checker to update component firmware - Di2 External Battery, battery charger, and power cable are universal between Dura-Ace 9070, 7970, Ultegra 6870, 6770 and Alfine Di2 systems - Battery weight: 71 grams
Significantly smaller, the SRAM eTap AXS BlipBox is now easier to integrate — mounting inside a stem faceplate cap, feed box, or frame. It's also AXS enabled, for easy personalization. Simple, intuitive, aero. - Replaces standard drop bar shift levers - Simple and intuitive eTap shift logic - AXS enabled for easy personalization - Limitless aero configurations - Two ports per side for Blips - Fits the included optional stem mount - Compatible with existing eTap Blips and Clics - Mounts inside stem faceplate cap, feed box or frame
SRAM eTap Battery is the power source for the eTap system. The same power unit is interchangeable between front and rear derailleurs. - Up to 1000 kilometers of riding per charge - Weight: 24g - Finish: Black - Compatibility: SRAM RED eTap
With Rokform's Bike Handlebar Mount your phone is visible, accessible, safe and secure thanks to the mount's easy-to-use locking design that lets you put your phone on and take it off in seconds (Rokform Universal Adapter or V.3 Mountable Case required for your phone and sold separately). With the industry’s only lever lock and adjustable handlebar strap you can rest assured your phone is safe. The simple, adjustable handlebar strap mount installs in seconds without tools and means that this mount can be removed and transferred to other bicycles with ease (or buy a separate mount for all your bikes!). The mount is even universal enough to work great on shopping and golf carts, and more!
Convert your K-Edge Garmin Computer Mount to be a Computer + Action Camera combination mount. Works with any camera that utilizes the GoPro sytle interface, including GoPro Hero, Garmin VIRB, and Shimano CM-1000. - Camera Adapter mount with GoPro style interface - Fits K-EDGE Garmin Mounts (K13-500, K13-505, K13-560) - Locks GoPro, Shimano, VIRB style cameras underneath Garmin Computer. - Centers camera in out of site position - Improves video clarity by removing plastic mount shake - Colors: Anodized Black - Weight: 14grams *Note: Garmin VIRB requires the GoPro adapter that is included in the box with the VIRB.
This NiteRider Adapter is sold separately from K-EDGE “Combo Mount." - Precision Machined 6061-T6 Aluminum - Anodized Gunmetal - Converts a NiteRider Rail Interface to adapt K-Edge GoPro Mounting Interface - Enables compatibility with K-Edge GoBig Mounts and Combo Mounts - 2x M4 Mounting bolts with Nylok included - Compatible with Lumina Series, Mako Series - Weight: 11.5 grams
The K-EDGE co-polymer insert for Garmin 1/4 Turn style computers is a replaceable item. While it is extremely strong, we designed this insert to fail on a significant impact before the tabs on the back of the Garmin break. - Qty 1 – K-EDGE Co-polymer Insert for Garmin 1/4 Computer (Part No. K13-503) - Qty 2 – M3 x 0.5mm x 6mm with Pre-Applied Nylon 180,18-8 S.S. Screws
Replacement plastic insert kit for K-EDGE Wahoo Mounts. The co-polymer insert for Wahoo 1/4-turn style computers is a replaceable item. While it is extremely strong, it is designed to fail on a significant impact before the tabs on the back of the Wahoo break. Attributes (specs): – Qty 1 – K-EDGE Co-polymer Insert for Wahoo 1/4 Computer (Part No. K13-1604) – Qty 2 – M3 x 0.5mm x 6mm with Pre-Applied Nylon 180,18-8 S.S. Screws
$49.99 - $54.99
Out-front computer mount for Wahoo Elemnt computers. This is the next generation of industry-leading Wahoo Computer Mounts – stronger, easier, more versatile, and more stylish design to compliment your Wahoo and your bike. The ultimate upgrade! The advanced co-polymer Wahoo insert locks your computer in place with strength and security. Designed and tested extensively so that our replaceable insert breaks away instead of your computer tabs in the event of a crash or mishap. *Compatible with the NEW Wahoo BOLT and Wahoo Mini - CNC Machined 6061-T6 Aluminum Platform, Injection Molded Wahoo Specific Co- Polymer - Compatibility – 31.8mm and 35mm diameter handlebars. - New clamp design is hinged for ease of installation. - Made in Boise, Idaho, USA. - Lifetime Guarantee against material or manufacture defects. Damages due to abuse or crashing excluded. *Attention: ASSEMBLY BOLTS NOT MEANT TO BE REMOVED OR TAMPERED WITH AT ANY TIME. K-EDGE Combo Mount are NOT DESIGNED to hold a Cycliq Fly 12. (Cycliq Fly 12 users should choose the K-EDGE K13-410, K13-420, K13-2450 GO BIG camera/light mounts.) K-EDGE mounts co-polymer plastic computer inserts are designed to hold the corresponding computer ONLY (Garmin- black, WAHOO- blue, SIGMA – red), and breakaway in a crash to protect the computer body. K-EDGE Combo Mounts are designed to hold Garmin, WAHOO and SIGMA cycling computers and Go Pro, Shimano, Garmin VIRB X sized cameras and standard sized cycling lights (Light and Motion Urban or Niterider). Please contact K-EDGE warranty manager Info@K-EDGE.com for questions or concerns. We highly suggest you follow the recommendations in the Garmin EDGE instructions that recommend use of the provided tether leash.
Monitor your pedaling cadence as you ride with Garmin's easy-to-install wireless sensor. The cadence sensor fastens to any crank arm size and measures pedal strokes per minute so you can get the most out of your training. Simply attach the sensor and ride. With no magnets or other exposed parts to line up, this sensor is easy to install, maintain, and move between bikes.
Monitor your speed and cadence as you ride with these easy-to-install wireless sensors. With no magnets or other exposed parts to line up, these sensors are easy to install, maintain and move between bikes. The speed sensor 2 attaches to the hub of either wheel and self-calibrates with your Edge cycling computer or compatible Garmin device to give you accurate speed and distance at all times — even without a head unit. The cadence sensor 2 fastens to any size crank arm and measures pedal strokes per minute so you can get the most out of your training. Send live speed, distance and cadence data to compatible training apps or displays by using ANT+ connectivity and BLUETOOTH Low Energy technology. With both of these sensors on your bike, you can work to improve your personal best or see where you stand against the pros.
Garmin's City Navigator is like having a front seat co-pilot who's awake and actually paying attention for once—in fact, it's even better than that. Whether you're traveling in a new state or unraveling tangled back-country roads in the hills of your hometown, you have a detailed road map every step of the way. Certain compatible Garmin devices give you turn-by-turn navigation and audible directions to keep you on route without having to stop to try and read the bleeding ink from your handwritten napkin directions. No back-tracking required. With 10 million points of interest, there are virtually endless options for fueling up, finding a hotel if you're on a tour, or even navigating back to the airport after a travel race.
Stay ahead of the pack with this extended out-front bike mount that lets you take full advantage of your Edge without compromising your ride. This mount with extended arm allows you to stay in a comfortable heads-up position for easier monitoring and improved safety.
Take your training to the next level with Garmin's Heart Rate Monitor Chest Strap. It's compatible with many of their GPS units and wirelessly gives you an accurate read out of your heart rate. Plus, it features ANT+ technology for seamless, interference-free data transferring. The front part of the strap contains the heart rate module and is made of flexible plastic while soft fabric goes around the back and is adjustable to your size.
Stay ahead of the pack with Garmin's Out-front Bike Mount that lets you to take full advantage of your Edge's capabilities without compromising your ride. The mount positions your device for easier monitoring and safety. Also compatible with the Forerunner 910XT and 310XT when used with a quick-release kit (sold separately).
- Micro Mount for Phones - Aluminum and composite construction securely holds any phone with any case for minimalist profile - Unique patent-pending design with proprietary stretch material grips your phone - Easy mounting under any standard stem. - Tighten to stem cap 6Nm torque.
The BlueGiga dongle gives Rouvy, CycleOps' virtual training software, the ability to seamlessly connect to Bluetooth devices and sensors. The BlueGiga dongle contains a Bluetooth (BLE) radio that allows PCs to communicate with BLE devices, including CycleOps smart indoor bicycle trainers and power meters made by the folks at PowerTap. Most importantly, the BlueGiga dongle is necessary to update the firmware Over the Air (OTA) via VirtualTraining for the Hammer and Magnus bike trainers. - Bluetooth dongle for PCs to work with Rouvy - Needed for Over the Air Firmware Updates to Smart Indoor Bike Trainers. - Works with PC desktops and laptops.
Cadence Magnet for all CatEye computers that record cadence.
Low Road position places the computer in front of the bar and nearly flush with the top of the bar, making for an easy to read display whether you are on the hoods or in the drops. - Sub-20 gram computer mount - Compatible with computers with 1/4 turn twist lock interface and 31.8mm bar surface - Single Torx T25 fixing bolt
Zipp delivers an uncomplicated computer mount for aerobar extensions that’s easy to install, lightweight, and vibration and slip free. The 22.3mm industry standard mount installs simply and securely on aero extensions. The Zipp QuickView TT Computer Mount is aerodynamically shaped for left-side installation, but also can be installed on the right bar extension. It comes with a single Torx T25 bolt, flexible mounting clamp, and a quarter-twist mount.
With aerobars, short stems and hydration systems crowding the front end of your bike, it's hard to mount a computer. But, with Xlab's Aero Computer Mount Gen 2 you can mount your computer to your stem cap! It's aero because it fits neatly behind aero drink systems and horizontally mounted bottles, and the extra height of the mount makes your computer easier to read. It can also be mounted on the Xlab Torpedo Mini Mount, placing your computer in front in your line of sight. • The Aero Computer Mount, re-designed! Aerodynamically designed and longer to support larger screen computers • Mount in front of Torpedo Systems or on stem bolt • Helps reduce drag from a computer mount with one that was designed with aerodynamics in mind • Mount in front of TORPEDO SYSTEM (sold separately) for optimum viewing. • Mount on stem when using non-XLAB drink systems (sold separately) • Easy to read when in aero position • Fits most computers including the new longer form factor models (sold separately) • Mount is 37 mm wide. Plenty of room to support the popular Garmin computers (sold separately) • Includes hardware and instructions • Weight: 29.5 grams
• When aerobar space is tight, place your computer on top • Tuck straw on either side for best aerodynamics • Fits on TORPEDO SYSTEM 100, TORPEDO SYSTEM 400 & REFILL UPGRADE KIT BOTTLES (each sold separately) • Compatible with most computers, including large screens (sold separately) • Glass-reinforced nylon • Weight: 18.5 grams
Aerodynamic dual-bottle BTA hydration system that features a dynamic, multi-position computer mount to accommodate your changing needs. Raise the computer mount up to tuck in a refill bottle for race day, or lower it down for a standard bottle while maintaining the optimal view for training days. - Telescoping Garmin mount features on-the-go tilt adjust to avoid glare. - Zero-leak design with a sealed viewing window to easily monitor liquid levels, and a leak-free Dolphin Breather Valve that lets air in but doesn't let water out. - Capacity: 26oz (768 mL) - Material: Plate: 6061-T6 Aluminum - Cage: Nylon Composite Vee Cage - Computer Mount: Nylon Composite - Bottle: Lead free, BPA-Free and HDPE food safe certified bottle - Brackets: Nylon composite with Velcro straps coated with no-slip extension grip - Adjustment Width: 75-150mm - Weight: 9.3oz (265g)
Telescoping Garmin Computer Mount for Versa Plates. Raise the computer up for Refill Bottles, or lower it down to clear Standard Bottles. On-the-go tilt adjust to avoid glare. - Telescoping computer mount makes for a seamless switch between Refill or Standard Bottle - Compatible with Garmin bike computers and Multisport Watches - Requires Versa Carbon Mount or Versa Aluminum Mount Telescoping Garmin-Specific Computer Mount - Raise the computer mount up to tuck in a Refill Bottle for race day, or seamlessly lower it down for a Standard Bottle to maintain the optimal view for training days. Compatible with Garmin bike computers and multisport watches. On-the-Go Computer Tilt Adjust - Avoid changing glare with a tilt mechanism for easy adjustments while you ride Arrives Fully Assembled - Few steps required to install and head out on your first ride - Weight: 1.9oz (54g) - Construction: Nylon Composite Includes - Fully assembled computer mount - 2 screw sets: one for Versa Carbon Plates, and one for Versa Aluminum Plates Warranty: Limited Lifetime
Gain more room or find the perfect position for lights, computers, music players, GPS, or whatever, with the Topeak BarXtender. Attaches securely to the handlebars or stem and adjusts for optimum position. - Clamp: Fits 22-38 mm tubes (shims included) - Crossbar: Device mount bar 25.4 mm - Material: Engineering Grade Plastic and Steel - Mount: Handlebar, Handlebar Stem - Size (L x W x H): 18 x 3 x 3 cm, 7.1” x 1.2” x 1.2” (folded) - Size (L x W x H): 13 x 10 x 3 cm, 5.1” x 3.9” x 1.2” (open) - Weight: 116 g / 4.08 oz
With this Tacx wireless ANT+ receiver for Android devices with a micro USB port, you can connect to devices that communicate via ANT+. For example a heart rate meter, speed and cadence sensor, sports watch, GPS device or bike computer. This enables you to keep track of your performance continually. It also allows you to link an ANT+ trainer to the Tacx Cycling app (tablet) or Tacx Training app (smartphone), or connect an older model Tacx trainer which only has ANT+ to your telephone, so you can train with the Tacx Training app and Tacx Cloud. The device you want to connect must have a micro USB port and Android 4.3 or higher. This ANT+ dongle is only compatible with devices that have USB On-The-Go.
Page 1 of 6 Next page