Skip to main content

Filter By:

  • Show More Sizes
  • Show Fewer Sizes

Park Tool

Park Tool Repair Stand Base
$229.95
Park Tool's 130 Repair Stand Base is designed for the PRS-3, PRS-3OSLB, PRS-3 OS-1, PRS-3 OS-2 and the PRS-23 LB Repair Stands (each sold separately). • 22-1/2" x 22-1/2" x 7/16" (57cm x 57cm by 1.1cm) steel plate • Approximately 68 lbs (31k) • Black painted
Park Tool Disc Brake Mount Facing Set
$465.95
The DT-5.2 is engineered and built to accurately face front or rear disc brake mounts so they are precisely aligned to the rotor. - Faces any IS Mount, Post Mount, or new Shimano Flat Mount, including low clearance, chainstay mounts - Telescoping axle adaptors allow use with any configuration of open or thru-axle dropouts and dropout widths (including Boost 110, Boost 148 and all fat bike axles) - Includes two facing cutters: IS Mounts Post and Flat Mounts - Includes storage case
Park Tool Replacement Clamp Covers
$9.90 - $25.08
Everyone wears out their Park Tool work stand clamp covers at some point. Find replacement covers for yours here. Each cover is constructed of soft, durable composite rubber. See below to determine which covers fit your Park Tool stand clamp: - 1002: fits 100-3X and 100-5X extreme range clamps - 1185: fits clamps on the repair stands PCS-9, PCS-10, PCS-11, and PCS-12 - 1259: fits 100-4X, 100-6X, 100-7X, and 100-15X clamps - 1960: fits 100-3D, 100-5D, and 100-25D Professional Micro Adjust Repair Stand Clamps - 468B: fits clamps with double cable reliefs, including 100-3C, 100-5C, 100-8C, 100-8Y, and 100-9C clamps - 467B: fits clamps with single cable relief, including PRS-2 through PRS-8 (for older-style clamps, non-current) - 468G: fits PCS-1 and PCS-2 clamps with double cable reliefs (clamp models: 100-1C, 100-1CA, and 100-2C) - 467G: fits PCS-1 and PCS-2 clamps with single cable relief (for older PCS-series stands only; not for current model stands) - 466: Rubber Replacement Clamp Cover Set (fits older clamps with plastic-dipped jaws)
Park Tool Frame Alignment Gauge
$55.95
Many bicycles will not shift or track properly because the front and rear wheels are not in line with the frame. If these conditions still exist after wheel and derailleur adjustments, the seat stays, chain stays, and rear drop outs of the frame may be misaligned. For years the accepted method to check the alignment of the rear drop-out was to run a string on either side. This method does work to some extent. However, it is not accurate because the measurement is not taken at the drop-out. With the Park Tool Frame Alignment Gauge, the alignment can be checked quickly and accurately at the drop-out. It includes a retractable pointer to fit all sizes and types of bicycles.
Park Tool Derailleur Hanger Alignment Gauge
$79.95
The DAG-2.2 is an indispensable shop tool that can be used to both measure and straighten misaligned derailleur hangers solving a high percentage of shifting problems. - Gauge bar made of heavy gauge, chrome plated steel - Adjusts to fit 20" to 29"+ wheels - Replaceable threaded tip - Upgraded large inner shaft for added strength* - Tighter tolerances for improved accuracy* - Improved clearance and reach to fit more frame/hanger combos including low clearance thru-axle derailleur hangers* *Compared to DAG-2
Park Tool Pedal Tap (1/2
$37.95
Clean out or restore damaged threads in crank arms with Park Tool's Pedal Taps. These taps can be used with either steel or alloy crank arms. The set includes both right- and left-hand threads. The 1/2" size is common on "one-piece" cranks. • Includes a set of 2 taps, 1/2" x 20 tpi • Made of high carbon steel, precision ground, and hardened to stay sharp • Fits all conventional tap handles
Park Tool Park Tool Cycling Socks
$15.49
Get yourself a pair or two of Park Tool's Cycling Socks, and show the world you work on your own rig. They're made in the USA out of cool-comfort 75% microdenier acrylic, 15% nylon, and 10% spandex with double-stitched heel and toe. They're great for riding, wrenching, and wearing confidently between your feet and your shoes.
Park Tool Tap Handle (1/4-inch)
$16.95
Made for the rigors of everyday shop use, this adjustable tap handle fits many common bicycle taps. • Fits most metric taps from M1.6-M8 • Fits most standard taps from #0-5/16”
Park Tool Reamer
$120.52 - $202.18
Park Tool offers premium-quality reamers for nearly any bicycle standard. The reamers below are designed to quickly, accurately, and precisely ream headtubes when used with Park's Head Tube Reamer (HTR), ensuring a perfect headset fit and prfoessional-quality bicycle build. Choose the correct reamer for your application using the following information: - 751.2: This reamer is sized to 30.1mm. This allows a 0.1mm interference fit when pressing the 30.2mm headset of the “Euro” one-inch standard. - 754.2: This reamer is sized to 33.9mm. The allows a 0.1mm interference fit when pressing the 34.0mm headset of the 1-1/8" standard. - 788: This reamer is sized to 43.95mm. It reams head tubes to accept “internal” headset cups with 44.05 - 44.10mm O.D. (1-1/8 ZS standard). It is used with Park Tool's 690-XL Facing Cutter and 750 Centering Cone. - 738: This reamer is sized to 52.1mm. It is used to ream head tubes using the 1-1/2" integrated headset standard. It is used with Park Tool's 690-XL Facing Cutter and 750.2 Centering Cone Adapter. - 789: This reamer is sized to 55.95mm. It is used to ream head tubes to accept “internal” headset cups with 56.00–56.10mm O.D. (1-1/2 ZS standard). It is used with Park Tool's 690-XXL Facing Cutter and #750 Centering Cone Adaptor. - 799: This reamer is sized to 47mm. It is used for cutting the lower head tube on frames using an IS47 bearing for a 1-1/4" integrated headset. It cuts a 45-degree bearing set shoulder.
Park Tool Dial Indicator for DT-3
$41.95
Dial Indicator Set bolts directly to the DT-3 allowing for greater accuracy and a way to measure results. Now includes an elongated, cylindrical tip that is large enough to work around voids in most rotors.
Park Tool Facing Pilot
$11.34 - $21.22
Park Tool has long provided some of the best cutting and machining tools in the bicycle industry. Their centering pilots demonstrate their commitment to maintaining this high level of quality. Please read below for use and compatibility information specific to each size pilot: - 49.8mm (for 1.5-inch standard): The 767 is used with the HTR-1 (HTR-1B) and 690XL facer to perform facing only. It fits head tubes with an inside diameter of 49.8mm (1.5" standard). - 43.8mm (for ZS44 and EC44): The 768 Pilot is used with the HTR-1 (HTR-1B), the 750 Centering Cone Adaptor and 690XL facer to perform facing only. It fits head tubes designed for low profile or, “zero-stack,” headsets. These head tubes have nominal inside diameters of 43.9mm. - 55.9mm (for internal 1.5-inch ZS): The 790 Pilot takes the place of the 789 Reamer when performing head tube facing only. The 790 is used with the HTR-1 Headtube Reamer, the 690-XXL Facing Cutter, and the 750.2 Centering Cone Adaptor. The tool allows facing head tubes with 55.95 – 55.90mm I.D. (“Internal” 1-1/2” ZS standard).
Park Tool Flat-Faced Socket Set
$54.95
Suspension maintenance and tuning require tools designed for a precise fit. The SKT-6 from Park Tools is a shop-quality set of six flat-faced sockets designed for use with common suspension fork fittings. Ideal for use with Park Tool Torque Wrenches, the 3/8-inch drive sockets are forged from tough chrome vanadium steel and chrome plated for lasting durability. - 24, 26, 27, 28, 30, 32mm flat-faced sockets - All sockets are 3/8" drive - Note: 27mm socket is tapered for better access on Suntour suspension forks
Park Tool Adjustable Torque Driver
$67.95
Shop-quality, adjustable torque driver that limits torque applied to fasteners, preventing over-tightening and damage to lightweight components. The ATD-1.2 features all-metal internal construction with a comfortable, ergonomic composite molded grip. Each tool is assembled and calibrated at Park Tool's factory in Minnesota.
Park Tool Crown Race Setting System — Oversized
$95.95
The CRS-15.2 uses two different insert rings to install bearing races on the 1.5-inch and 1-1/4-inch forks. The bearing surface is spared a direct hit by using aluminum inserts. Using a hammer, tap firmly on the end cap of the tube and seat the race into its proper place safely and accurately. Included extension allows work on fork steering tubes up to 425mm. - SHIS terminology: The CRS-15 services crown races in SHIS 33 and 40.
Park Tool TSB-4 Tilting Truing Stand Base
$57.95
Securely holds the TS-4 Professional Wheel Truing Stand and tilts 20 degrees from front to back for comfortable wheel work and sight lines at any bench height. Features a wide, sturdy base, small parts compartments, spoke wrench holders, and is constructed of a durable composite material.
Park Tool Right Hand Bottom Bracket Tap
$305.32 - $338.74
Park Tool's Right Hand Bottom Bracket Tap is a replacement tap for their BTS-1 Bottom Bracket Tap Set (sold separately). This tap is used on the non-drive or left side of the bike, which uses a clockwise or "right hand threading." Two taps are required for use.
Park Tool Rolling Big Blue Box
$499.95
Built to withstand the punishment of travel and constant use and molded from impact resistant polypropylene, the BX-3 features pallets with 70% more surface area than the BX-2.2. Easily transportable with the integrated wheels and extendable handle, this case was designed with the help of some of the world's best mechanics for optimal form, function and longevity. - Smooth rolling integrated wheels - Extendable handle - Dust and water resistant - Air pressure compensation valve - Custom designed tool-holding pallets with loops and pockets - Gas assisted lid struts for easy opening - Dual-sided upper and mid level folding pallet wings - Front tool pallet that stores safely inside during transport - Nominal dimensions: 23.4" x 17.3" x 9.3" (59.5 cm x 44 cm x 23.5 cm), 21.6 lbs. (9.8 kg)
Park Tool MTC-30 Multi-Tool
$21.95
The MTC-30 features a super strong, composite, multi-position handle, with hardened and plated tools and smooth ergonomic operation. Lightweight, compact, and perfect to carry along. - 2.5, 3, 4, 5, 6 and 8mm hex wrenches - T25 & T30 Torx compatible drivers - Combo cross/straight tip screwdriver - 8 & 15mm box wrenches - Key ring holder - Weight: 131g (4.62 ounces)
Park Tool Bottle Opener
$7.95
Make quick work of any bottle-cap-removal operation with Park's BO-2 Bottle Opener. This ergonomic tool is made of stainless steel with a comfy vinyl coating.
Park Tool Crown Race Setting System (1, 1-1/8 -inch)
$84.95
Quickly, safely and easily set your crown race with Park's CRS-1 Crown Race Setting System. It includes 6 different inserts (3 for 1-inch and 3 for 1-1/8-inch steerer tubes) that ensure full contact with the crown race for precision installation.
Park Tool Double-Ended Cone Wrench
$5.95
Park's Double-Ended Cone Wrenches are designed for home mechanics. They're made of thin tool steel to fit the low-clearance adjusting nuts and cone flats on a variety of bearing assemblies. Each wrench is chrome plated for long life and available in popular combinations from 11 to 18mm. Most applications require a pair of cone wrenches. Call or stop by. We can recommend the correct sizes for your needs.
Park Tool Chain Whip/Pedal Wrench
$23.95
Park adds versatility to your toolbox with their combination Chain Whip/Pedal Wrench. It features a chain whip for cassette removal on one end and a 15mm pedal wrench for installing and removing pedals on the other.
Park Tool I-Beam Mini Fold-Up Hex Wrench/Screwdriver/Torx Set
$16.95
Park's I-Beam Mini Fold-Up Screwdriver/Torx Set includes 1.5, 2, 2.5, 3, 4, 5, and 6mm Allen wrenches, a socket 8mm Allen, a regular screwdriver and a T25 Torx tool (for disc-rotor bolts). The I-Beam conveniently fits in pockets and packs, too.
Park Tool Spoke Wrench For Mavic Wheel Systems
$12.49
Because even your super-fast Mavic wheels will eventually need truing, Park designed the Spoke Wrench For Mavic Wheel Systems. This comfortable, vinyl dipped, two-sided spoke wrench is designed to easily access Mavic fittings. Plus, it fits both Mavic 9mm threaded eyelets and 5.65mm integrated nipples.
Park Tool Fixed-Gear Lockring Wrench
$17.95
Park's Fixed-Gear Lockring Wrench features 2 different radius hooked spanners for a precise fit, and easy removal and tightening of most fixed-gear lockrings. The HCW-17 fits rings with an outside diameter of 41 to 44mm. It also fits BMX cassette hub lockrings with external notches.
Park Tool Pedal Wrench Crow Foot
$14.95
Park Tool's Pedal Wrench Crow Foot is used with any 3/8” drive torque wrench to verify pedals are torqued to the correct spec. The TWB-15 is laser cut, heat treated and plated for long life.
Park Tool Storage Hook - Wood Thread
$5.49
• Park Tool Storage Hooks are perfect for hanging bikes, wheels, etc. • Vinyl coated to prevent scratching. • Wood threaded • Made from 7mm steel rod • For a pilot hole in wood, use a 1/4" or 6mm bit • Sold in pairs
Park Tool Hex Wrench (8mm)
$5.95
Park's Hex Wrenches are every mechanic's best friend. They are constructed from industrial quality steel for durability and feature chamfered tips for a precision fit. And, their convenient L shape is perfect for jobs that require lots of leverage or for getting to hard-to-reach bolts.
Park Tool Needle Nose Pliers
$25.95
Park's Needle Nose Pliers are professional quality, 6-inches long, and made from forged, heat-treated chromoly steel. For ease of use they have a hidden spring, cutting jaws and 5 different gripping and crimping areas. Plus, they have soft-touch, dual-density handles for an excellent grip.
Park Tool Park Tool Mechanic's Gloves
$24.95
Great for riding, mechanical work, or to just show off the colors of your favorite tool brand, the GLV-1 is the perfect combination of comfort and function. - Digital Amara palm with anatomically shaped external reinforcement patches - Touch phone compatible thumb and index fingertips - Comfortable, soft fleece brow wipe - Durable two-way stretch knit glove back with knuckle gussets - TPR adjustable closure tab